FAQ – Questions & AnswersCategory: Remington FAQHow to adjust an old Remington 700 trigger?
Hugh Ramos asked 1 month ago
What tools do I need to adjust an old Remington 700 trigger?

6 Answers
Cruz Staff answered 1 month ago

If you’re adjustment-savvy, it’s not hard to do justice to an old Remington 700 trigger. Just remember that while the task may be easy, safety is always paramount when working with firearms. With that in mind, here are the basics of how to adjust an old Remington 700 trigger.

Start by removing the stock and magazine (if applicable). Next, locate the screws that secure the action to the stock. These screws can usually be found near the front and rear receiver rings. With the action free from the stock, take a look at the trigger itself. In most cases, you’ll see two adjustment screws – one for sear engagement and one for overtravel.

How to adjust an old Remington 700 trigger?

To adjust sear engagement, start by cocking the hammer and placing the safety in the “on” position. Next, use a small punch or Allen wrench to back out the sear engagement screw until it’s just barely touching the trigger sear. Once you have a good feel for where that “sweet spot” is, tighten the screw down until you see a very small amount of resistance. This will help ensure that your adjustments are precise.

Overtravel can be adjusted in much the same way, but you’ll want to start with the overtravel screw backed out. Adjusting overtravel is a bit more forgiving than sear engagement, so you don’t need to be as precise. Just make sure that you don’t adjust the screw so far that it no longer contacts the trigger sear.

With both screws properly adjusted, reassemble the rifle and test the trigger pull. If it feels too light or too heavy, simply readjust the screws until you get the desired result. As always, be sure to test the rifle’s safety features after making any adjustments to the trigger.

Lewis Staff answered 1 month ago

If you’re adjusting an old Remington 700 trigger, there are a few things to keep in mind. First, make sure that the gun is unloaded and that the safety is on. Then, take a look at the screw that holds the trigger in place. This screw is usually located at the front of the trigger guard, and it can be turned clockwise or counterclockwise to adjust the trigger pull weight. To make the trigger lighter, turn the screw counterclockwise; to make it heavier, turn it clockwise. It’s important not to over-tighten the screw, as this can damage the trigger.

How to adjust an old Remington 700 trigger?

Once you’ve adjusted the screw, test the trigger by pulling it slowly and steadily. If it feels too light or too heavy, readjust the screw until you find a setting that feels comfortable. Remember, a lighter trigger pull can be beneficial for accuracy, so don’t be afraid to experiment. Once you’ve found the perfect setting, make sure to test the gun thoroughly before taking it out into the field.

Olson Staff answered 1 month ago

The Remington 700 is a popular rifle, and many people enjoy shooting it. However, the trigger can be a bit finicky, and sometimes it needs to be adjusted. Luckily, this is a relatively easy process that anyone can do at home with just a few tools.

First, you will need to remove the action from the stock. This is usually pretty easy to do – there are usually two screws that hold the action in place, and you can simply unscrew them and pull the action out. If you have any trouble with this, consult your gun’s manual or ask someone at your local gun shop for help.

Once the action is out of the stock, take a look at the trigger assembly. There should be a small setscrew near the front of the trigger (on the side that faces the stock). This set screw is what adjusts the trigger pull weight. To adjust the trigger pull, simply turn this setscrew clockwise to increase the weight, or counterclockwise to decrease it.

Once you have adjusted the setscrew to your desired setting, replace the action in the stock, and screw it back in place. That’s all there is to it! With just a few minutes of work, you can easily adjust the trigger pull on your Remington 700 rifle.

How to adjust an old Remington 700 trigger?

Jordan Staff answered 1 month ago

There are several ways to adjust an old Remington 700 trigger.

You can adjust:

  • the sear engagement,
  • the trigger pull weight,
  • the length of travel.

How to adjust an old Remington 700 trigger?

To adjust the sear engagement, you’ll need to remove the stock and then unscrew the adjustment screw located under the bolt release case. This will change how much contact there is between the sear and trigger.

To adjust the trigger pull weight, you’ll need to remove the stock and then loosen or tighten the tensioning screw located behind the trigger guard. This will change how much force is required to pull the trigger.

To adjust the length of travel, you’ll need to remove the stock and then loosen or tighten the setscrew clockwise or counterclockwise. This will change how far the trigger travels before it resets.

Antony Staff answered 1 month ago
There are a few things you can do to adjust an old Remington 700 trigger.

  1. Make sure the gun is unloaded and that the safety is on.
  2. Take a look at the trigger assembly and see if there are any adjustment screws. If there are, you can use these to adjust the trigger pull weight and sear engagement.
  3. Test the trigger by dry firing the gun into a safe backdrop.

Ivan Staff answered 1 month ago
If you have an old Remington 700 trigger that needs adjustment, there are a few things you can do to make it work like new again.

  • First, check the screws that hold the trigger in place. Make sure they are snug, but not too tight.
  • Next, check the trigger return spring. It may be weakened or broken, and this can cause problems with the trigger pull.
  • Finally, take a look at the sear engagement surfaces. If they are damaged or worn, they will need to be replaced.

With a little bit of care and attention, your old Remington 700 trigger can be working like new again in no time!
 
How to adjust an old Remington 700 trigger?