Nickel boron BCGs are known for their amazing slickness, which helps reduce wear on the firearm. However, as with all firearms, proper cleaning and maintenance are essential for optimal performance and longevity.
First and foremost, be sure to unload your firearm before starting any cleaning process. Also, make sure that the barrel is clear of any obstructions before beginning. For best results, use a quality gun cleaning solvent specifically designed for firearms. Apply the solvent to a clean cloth or patch, and then wipe down the entire BCG surface. Be sure to pay special attention to the firing pin assembly and bolt carrier rails.
Afterward, use a stiff brush (such as a toothbrush) to scrub away any remaining residue. Once you are satisfied that the BCG is clean, rinse it off with clean water and dry it completely with a lint-free cloth.
It is also a good idea to apply a thin layer of gun oil to all metal surfaces, including the bolt carrier key (if applicable). This will help protect the metal from corrosion and keep it functioning smoothly.
Nickel boron BCGs are prized for their self-lubricating properties, which make them ideal for use in firearms. However, these benefits come at a cost, as nickel boron BCGs are more difficult to clean than traditional BCGs.
The first step in cleaning a nickel boron BCG is to identify the type of dirt or fouling that has built up on it. This can be done by examining the BCG under a microscope or by using an electronic borescope. Once the type of dirt or fouling has been identified, the appropriate cleaning method can be selected.
For example, if carbon build-up is the primary contaminant, then a degreaser such as Break-Free CLP may be used. However, if lead or copper fouling is present, then an ammonia-based cleaner such as Hoppe’s No. 9 should be used.
Once the appropriate cleaning solution has been selected, the BCG should be placed in an ultrasonic cleaner and allowed to soak for the recommended amount of time. After soaking, the BCG should be rinsed with clean water and dried with a lint-free cloth.
Once the BCG is clean, it can be lubricated with a quality gun oil or grease.
Nickel boron BCGs are a popular choice for AR-15 rifles because of their self-lubricating properties. This means they require less lubrication and maintenance than other BCG types. However, like any other firearm component, they need to be cleaned and maintained regularly to ensure optimal performance.
Here’s a basic guide on how to clean nickel boron BCGs:
- Make sure the rifle is unloaded and pointed in a safe direction.
- Disassemble the rifle according to the manufacturer’s instructions.
- Remove the BCG from the upper receiver and clean it using a bore brush, solvent, and rags. Be sure to clean the gas key, bolt carrier body, and all other parts of the BCG.
- Inspect the BCG for any damage or wear. If any damage is found, replace the component.
- Lubricate the BCG according to the manufacturer’s instructions.
- Reassemble the rifle and test it to make sure it is functioning properly.
Nickel Boron BCGs are known for their high levels of accuracy and corrosion resistance. As such, it’s important to clean them regularly and properly to maintain their performance.
The best way to clean a nickel boron BCG is with soap and water. First, remove any debris or fouling from the surface of the BCG with a brush or cleaning rod. Then, wet your hands and work some soap into a lather. Rub the lather over the entire surface of the BCG, making sure to get into all the nooks and crannies. Rinse off the BCG with warm water, then dry it off with a towel or cloth.
Nickel boron BCGs are very easy to clean. Just use a brass brush and some Hoppe’s #9 to clean out the carbon fouling. For more stubborn fouling, you can use a light coat of gun oil or Kroil penetrating oil to help loosen it up. Then just use a bore brush to scrub it out.
There is a lot of debate on the best way to clean nickel boron BCGs. Some people say you should never use harsh chemicals or solvents on them, while others say that you need to use aggressive chemicals to remove all the carbon.
The truth is that there is no one-size-fits-all answer when it comes to cleaning nickel boron BCGs. Every gun is different, and each will require its specific cleaning method. However, some basic tips that can be used as a general guideline include using an ammonia-based cleaner like Hoppes #9 to dissolve carbon build-up, using an ultrasonic cleaner with distilled water to remove any debris or residue, and using a toothbrush or other soft-bristled brush to scrub the inside of the BCG’s chamber.
Please login or Register to submit your answer