FAQ – Questions & AnswersCategory: Gun Cleaning FAQHow to clean a Taurus judge revolver?
Stanley Hopkins asked 1 year ago
What can you clean a revolver with?

6 Answers
Lewis Staff answered 1 year ago

There are a few things you’ll need to clean your Taurus Judge revolver: a soft cloth, some gun oil, and a cleaning rod.

How to clean a Taurus judge revolver?

Once you have these supplies, follow these steps:

1. Start by unloading your revolver. Make sure to remove all the rounds from the cylinder before proceeding.

2. Visually inspect the revolver to make sure there is no debris or dirt on the surface of the gun. If there is, use the soft cloth to gently wipe it away.

3. Next, open up the cylinder and using the cleaning rod and gun oil, lightly lubricate all moving parts within the cylinder. Be sure not to over-lubricate as this can attract dirt and debris.

4. Close the cylinder and give the revolver a once-over to make sure everything is in working order.

5. Finally, re-load your revolver and you’re good to go!

If you have any further questions about cleaning your Taurus Judge revolver, please consult the owner’s manual or contact a qualified gunsmith.

Cruz Staff answered 1 year ago

There are a few things you need to do to clean a Taurus Judge revolver properly. First, make sure that the gun is unloaded and there is no ammunition present. Next, disassemble the revolver by removing the cylinder and barrel. Once the revolver is disassembled, you can start cleaning each part individually.

To clean the cylinder, use a brass brush and some cleaning solvent to remove any build-up of dirt or debris. Be sure to also clean out the crane assembly area where the cylinder meets the frame. Once the cylinder is cleaned, dry it off with a soft cloth and lightly lubricate it before reassembling the gun.

As for cleaning the barrel, start by using a cleaning rod and patch to remove any fouling from the bore. Be sure to also clean the muzzle area and under the extractor star. Once the barrel is clean, dry it off with a soft cloth and apply a light coat of oil before reassembling the gun.

Finally, wipe down the entire frame of the revolver with a damp cloth to remove any fingerprints or other debris. Once the frame is clean, you can reassemble the gun and it will be ready for use.

Olson Staff answered 1 year ago

If you’re looking to clean your Taurus Judge revolver, there are a few things you’ll need to do. First, make sure that the gun is unloaded and that there is no ammunition present. Next, disassemble the gun by removing the cylinder and Barrel Assembly. Once the gun is disassembled, you can start cleaning each piece.

The cylinder can be cleaned with a softer brush, like a toothbrush, to remove any debris or buildup that might be present. The Barrel Assembly can be cleaned with a solvent-soaked patch followed by a dry patch. Finally, using a cleaner and lint-free cloth, wipe down the entire frame of the revolver.

With regular cleaning and maintenance, your Taurus Judge revolver should continue to function properly for many years to come.

Jordan Staff answered 1 year ago

If you’re the owner of a Taurus Judge revolver, then you know that it’s a great gun for both self-defense and target practice. But like any gun, it needs to be properly cleaned and maintained to function at its best.

How to clean a Taurus judge revolver?

Here’s a quick guide on how to clean your Taurus Judge revolver:

Tools and materials needed:

  • Cleaning rod
  • Patch bore snake or another cleaning patch (try not to use cotton swabs as they can leave behind lint)
  • Gun oil or solvent
  • A soft cloth

1. Begin by unlatching the cylinder from the frame of the revolver. Pry open the cylinder using the indexing notch located on the left-hand side of the frame.

2. With the cylinder open, inspect each chamber for any dirt, debris, or powder residue. Use the cleaning rod to lightly scrub the chambers clean if needed.

3. Once the chambers are clean, insert the patch bore snake into the muzzle of the barrel and run it through a few times to remove any residue from inside.

4. Next, apply a few drops of gun oil or solvent onto a soft cloth and wipe down the exterior of the revolver, taking care to avoid getting any oil on the grips or in the trigger mechanism.

5. Finally, reassemble your revolver and give it a once-over to make sure everything is properly in place before putting it away.

By following these simple steps, you can keep your Taurus Judge revolver in top condition for years to come.

Antony answered 1 year ago

There are a few different ways to clean a revolver, but the basics are always the same. First, you’ll need some supplies. You’ll need a cleaning rod, cleaning patches, and a good solvent. You’ll also need some gun oil and a rag.

Start by removing the cylinder from the frame of the revolver. Once the cylinder is removed, you can start cleaning each chamber individually. Run a patch through each chamber with solvent on it to remove any fouling or debris. Be sure to clean both the inside and outside of the chambers.

Once all of the chambers are clean, you can start on the rest of the revolver. Use your cleaning rod to run solvent through all of the nooks and crannies of the gun. Be sure to pay special attention to the forcing cone (the area where the cylinder meets the barrel) and the ejector rod.

Once you’re satisfied that the entire revolver is clean, you can start oiling it. Use a rag to apply a light coat of oil to all of the metal surfaces. You don’t want to over-oil your revolver, so be sure to wipe off any excess before reassembling it.

Cleaning your revolver regularly will help keep it in good shape and ensure that it continues to function properly.

How to clean a Taurus judge revolver?

Ivan Staff answered 1 year ago

If you’re looking to clean your Taurus Judge revolver, there are a few things you’ll need to do. First, make sure that the gun is unloaded. Next, disassemble the gun according to the manufacturer’s instructions. Once the gun is disassembled, use a brush and cleaning solvent to clean all of the parts. Be sure to thoroughly dry all of the parts before reassembling the gun.

How to clean a Taurus judge revolver?