FAQ – Questions & AnswersCategory: Ammo FAQHow to reload pistol ammo?
Huss asked 2 years ago
How long does it take to reload pistol ammo?

5 Answers
Lewis Staff answered 2 years ago

First and foremost, always follow the Four Rules of Gun Safety:

  1. Treat all guns as if they are always loaded.
  2. Never point a gun at something that you are not willing to destroy.
  3. Keep your finger off the trigger until your sights are on target and you are ready to shoot.
  4. Be sure of your target and what is beyond it.

With that established, let’s outline the basics of reloading pistol ammunition:
The first step is to gather your supplies. You will need:

  • A set of scales
  • A powder measure
  • A loading block
  • A case tumbler
  • Pistol dies appropriate for the caliber you wish to load
  • A shell holder that fits your press
  • Primers
  • Powder
  • Bullets

Once you have all of your supplies, you will need to set up your work area. Make sure you have a well-ventilated area with plenty of light. You should also have a sturdy table or workbench to avoid making any mistakes.
The next step is to clean your brass. This can be done in several ways, but the most common method is to use a case tumbler with some sort of media, like crushed walnut shells. This will remove any dirt, grit, or grime that has built up on the brass and could potentially damage your dies or cause a misfire.
After the brass is clean, you will need to resize and deprime it. This is done by running the brass through a set of pistol dies. The die will resize the brass back to its original dimensions and also remove the spent primer.
Once the brass is resized and deprived, it is time to start reloading. The first step is to prime the brass. This is done by using a small tool to place a new primer in the primer pocket of the brass. Make sure that the primer is seated flush with the case or you may have problems down the road.
The next step is to measure out your powder. This is where a powder measure comes in handy. You want to be very careful when measuring powder as too much or too little can cause problems. Once you have the appropriate amount of powder, you will need to pour it into the brass. Be sure to tap the side of the brass so that the powder settles evenly.
The next step is to seat the bullet. This is done by using a loading die with a bullet seating plug. The die will guide the bullet into the brass and seat it at the correct depth. Be sure that the bullet is seated flush with the case or you may have problems down the road.
Once the bullet is seated, you will need to crimp the brass. This is done by using a loading die with a crimping plug. The die will crimp the brass around the bullet to ensure that it does not move during recoil.
And that’s it! You have now successfully reloaded your pistol ammunition.

The best ammo for your gun here.

Cruz Staff answered 2 years ago
There are a few different ways to reload pistol ammo, and the best method for you will depend on your circumstances. If you’re just looking to save money on ammunition, then reloading your rounds is a great way to do that. However, if you’re also looking for improved accuracy and performance, then you’ll want to consider spending a little more time and effort on your reloads. Here are a few basic tips on how to reload pistol ammo:
1) Start with good-quality brass cases. Once fired, many brass cases will end up slightly misshapen. This can cause problems with feeding and firing, so it’s important to start with high-quality brass that has been properly resized.
2) Choose the right powder for your reloads. Different powders will produce different results, so it’s important to choose one that is appropriate for your intended use.
3) Be very careful when measuring powder charges. Overloading a case can lead to dangerous pressure levels, so it’s important to be precise when measuring powder charges.
4) Use a good quality bullet. Cheap bullets can be inaccurate and may not perform well in self-defense situations. It’s important to use a high-quality bullet that will shoot accurately and perform well in a self-defense situation.
5) Make sure your reloads are properly seated in the cases. Properly seated reloads will feed more smoothly and fire more reliably than ones that are not properly seated.
6) Inspect each reloaded round carefully before using it. Look for any signs of problems, such as dents in the brass or bulges in the case. If you see any potential problems, discard the round and start over.

Olson Staff answered 2 years ago
Whether you’re a first-time gun owner or a seasoned marksman, knowing how to reload your ammunition can be a valuable skill. Not only can it save you money, but it also allows you to customize your ammunition to fit your specific needs. In this article, we’ll show you how to reload pistol ammo step-by-step so that you can get started right away.
Tools and Materials 
To reload pistol ammo, you’ll need the following tools and materials: 

  • A Reloading Press 
  • Shell Holders 
  • Pistol Dies 
  • Rock Chucker Priming Tool 
  • Powder Scale 
  • Powder Trickler 
  • Rifle Powder Funnel 
  • Pistol Powder Funnel 
  • Reloading Manual 
  • Primers 
  • Bullets 
  • Cleaning Rod and Brush Set 

Step 1: Preparing the brass 
The first step in reloading pistol ammo is to prepare the brass. Start by cleaning the brass using a cleaning rod and brush set. Once the brass is clean, you’ll need to resize it using a reloading press and pistol dies. Resizing is important because it ensures that the brass will fit snugly in the chamber of your gun. 
Step 2: Charging the cases 
After the brass has been resized, you’ll need to charge the cases with powder. Using a powder scale, measure out the appropriate amount of powder for each case. Then, use a powder trickler to fill the cases with powder. Be sure to use the correct type of powder for your gun. 
Step 3: Seating the bullets 
Once the cases have been charged with powder, you’ll need to seat the bullets. To do this, first, place the bullet on top of the case. Then, use a reloading press to push the bullet into the case until it is seated firmly against the powder charge. 
Step 4: Crimping the cases 
After seating the bullets, you’ll need to crimp the cases. This step is important because it ensures that the bullets will not move when the gun is fired. To crimp the cases, simply run them through the reloading press with a crimping die. 
Step 5: Inspecting the ammunition 
Once you’ve completed all of the steps above, your ammunition is now ready to be fired. However, it’s always a good idea to inspect each round before firing to make sure that everything is in order. Look for any signs of damage to the brass or bullets, and make sure that the powder charges are correct. 

Jordan Staff answered 2 years ago

If you’re a gun owner, chances are you know how to reload ammunition. Reloading is a process where spent shells or cartridges are reused by reinserting new bullets and primers. For many shooters, reloading is a fun and satisfying hobby that can save money in the long run. Plus, it’s a great way to customize your ammunition to fit your specific needs.
Before you get started, you’ll need to gather a few supplies. Here’s a list of what you’ll need:

  • Reloading press
  • Reloading dies
  • Shell holders
  • Powder measure
  • Scale
  • Funnel
  • Priming tool
  • Case trimmer
  • Ammo boxes or trays

The first thing you’ll need is a reloading press. This is the main piece of equipment used in the reloading process. There are many different types and styles of presses available on the market, so it’s important to choose one that best suits your needs. A turret press is a good choice for beginners, as it can be used for both single and double-stage reloading. Once you have your press set up, you’ll need to purchase reloading dies. Dies are specialized tools that are used to resize, deprime, and prime brass cases. You’ll need a separate die for each caliber you plan on reloading. Shell holders are another important piece of equipment, as they’re used to hold the brass case in place while it’s being worked on.
Powder measures are used to dispense the correct amount of powder into each case, while scales are used to weigh the powder charges. Funnels help to pour the powder into the cases, and priming tools are used to install new primer shells into the cases. Case trimmers are used to trim down brass cases that have become too long from repeated reloading. Finally, ammo boxes or trays are used to store the finished rounds.
The Steps Involved
Now that you have all the necessary equipment, let’s go over the steps involved in reloading pistol ammunition. The first step is to resize the brass cases. This is done by running them through the sizing die. Next, the cases need to be deprived. This removes the spent primer from the case so that a new one can be installed. Once the cases are deprived, they need to be primed. This involves installing a new primer shell into the case.
Once the cases are primed, it’s time to add powder. Powder measures are used to dispense the correct amount of powder into each case. The next step is to seat the bullet. This involves seating the bullet into the case so that it’s flush with the case mouth. Finally, the cases need to be crimped. This ensures that the bullet is properly secured in the case.
Safety Tips
There are a few safety tips to keep in mind when reloading pistol ammunition. First, always make sure that your work area is clean and well-lit. Second, always follow the manufacturer’s instructions for each piece of equipment you’re using. Third, pay close attention to what you’re doing and double-check your work as you go. Finally, make sure to store your finished rounds in a safe place away from children and pets.

Ivan Staff answered 2 years ago