FAQ – Questions & AnswersCategory: Sig Sauer FAQHow to disassemble a Sig Sauer?
Timothy Park asked 6 days ago
Can i to disassemble a Sig Sauer?

4 Answers
Antony Staff answered 6 days ago

To disassemble a Sig Sauer, you will need the following tools:

  • A screwdriver that fits the screws on your gun
  • A punch or a dowel to depress the spring pins
  • A cleaning rod or other long object to push out the barrel and recoil spring assembly

Once you have those tools, follow these steps:

1. Make sure your gun is unloaded and pointed in a safe direction.

2. Remove the magazine and check the chamber to ensure there is no rounds present.

3. Using a screwdriver that fits the screws on your gun, remove the grip panels.

4. Depress the spring pins using a punch or dowel. There are two on each side of the frame.

5. Push out the barrel and recoil spring assembly using a cleaning rod or other long object.

You have now successfully disassembled your Sig Sauer! Proceed with cleaning and reassembly as desired.

We’ve also picked out the best Sig P365 holster

Cruz Staff answered 6 days ago

There are a few Sig Sauer models, so make sure you are following the correct instructions for your specific firearm.

Here is a general guide on how to disassemble a Sig Sauer pistol:

1. Make sure the gun is unloaded and pointed in a safe direction.

2. Remove the magazine by pressing down on the magazine release button and pulling it out of the gun.

3. Rack the slide back to eject any rounds that may be in the chamber.

4. Withdraw the slide lock lever located on the left side of the frame above the trigger guard, and pull the slide forward off of the frame rails (you might have to wiggle it a bit). Now you can remove the barrel assembly from the slide.

5. To remove the recoil spring, hold the barrel and compress the spring. While compressed, unscrew and remove the spring plug. Let the spring decompress slowly.

6. The breech block can now be removed from the rear of the barrel by depressing the firing pin safety (located on top of the breech block) and pushing out rearward on the breech block.

7. Finally, you can remove the firing pin assembly from the breech block by pulling it to the rear until it disengages from its locking notch, then tipping it forward out of the breech block.

With these instructions, you should be able to disassemble your Sig Sauer pistol for cleaning or other maintenance purposes. Remember to reassemble in the reverse order, and always double-check that your gun is unloaded before disassembling it.

Olson Staff answered 6 days ago

There are a few ways to disassemble a SIG Sauer.

The quickest and easiest way is to use the following steps:

1. Make sure the gun is unloaded and pointed in a safe direction.

2. Remove the magazine by depressing the magazine release button located on the left side of the frame below the trigger guard.

3. Rack the slide back and lock it open by depressing the slide stop lever, located on the left side of the frame above the trigger guard.

4. Rotate barrel lock 180 degrees counterclockwise (as viewed from muzzle end) and remove the barrel from the receiver.

5. Remove recoil spring guide rod assembly by a depressing plunger on the end and rotating the rod counterclockwise (as viewed from the muzzle end) until it can be pulled out of the front of the slide.

6. Remove recoil spring and barrel bushing by compressing spring and turning to bush clockwise (as viewed from muzzle end) until it releases from spring guide.

7. Remove the breech block by depressing the extractor and sliding the breech block forward out of the slide.

We also recommend that you watch this video

Jordan Staff answered 6 days ago

You will need a screwdriver to remove the screws on the bottom of the gun.

  • Once the screws are removed, you can separate the two halves of the gun. There is a small pin that holds the hammer in place. You will need to use a punch or a sharp object to push out the pin.
  • After pushing out the pin, you can remove the hammer and trigger assembly. The recoil spring is located under the barrel. You can easily remove it by pulling it out from underneath.
  • Lastly, you can remove the barrel and slide it by unscrewing the barrel nut.