FAQ – Questions & AnswersCategory: Gun Barrel FAQHow to remove Remington 700 barrel?
Caleb asked 3 months ago
Can i remove Remington 700 barrel?

5 Answers
Antony Staff answered 3 months ago

The first thing you’ll need to do is remove the stock. Depending on the model of your Remington 700, there may be a few screws that need to be removed to do this. Once the stock is off, you should be able to see two large screws near the front of the receiver. These screws hold the barrel in place, so you’ll need to remove them to take the barrel off.

With the stock and receiver separated, you should now be able to see the inside of the gun where the barrel fits. There may be a small amount of residue or grease on the surface, but don’t worry about cleaning it off just yet. Take a close look at how the barrel fits into the receiver and make note of any washers or other parts that may be in place. You’ll need to put these back in the same order when you reassemble the gun, so it’s important to pay attention to their placement.

Once you have a good understanding of how everything fits together, you can begin the process of removing the barrel. Start by unscrewing the two large screws that hold it in place. With those screws removed, the barrel should now be loose in the receiver. You may need to wiggle it a bit to get it free, but be careful not to damage any of the parts. With the barrel removed, you can now clean all the surfaces that come into contact with it. This is a good time to inspect the barrel for any wear or damage and make sure it’s still in good condition.

If everything looks good, you can now begin the process of reassembling the gun. Start by putting the barrel back into the receiver and loosely tightening the two large screws. Once the barrel is in place, you can now reattach the stock. Make sure all the screws are tight and that the stock is secure before moving on. With the stock back in place, you can now check to see if the gun is still functioning properly. If everything looks good, you’re all done!

Ivan Staff answered 3 months ago

If you own a Remington 700 rifle, chances are you’re interested in shooting long-range accurately. To do that, you need to start with a good barrel. But what if your barrel is damaged or worn out? Is it possible to remove and replace the barrel on a Remington 700?

How to remove Remington 700 barrel?

Yes, it is possible to remove and replace the barrel on a Remington 700 rifle. However, it’s important to note that this is not a do-it-yourself project. The process requires special tools and expertise, so it’s best left to a qualified gunsmith.

Here are the steps involved in removing and replacing the barrel on a Remington 700:

  1. Start by removing the stock. This will give you access to the action screws, which need to be loosened to remove the barreled action from the stock.
  2. Next, remove the barreled action from the stock.
  3. Once the barreled action is removed, you’ll need to remove the old barrel. To do this, first, remove the front sight assembly. Next, unscrew the barrel nut, which is located just behind the front sight assembly. With the barrel nut removed, the old barrel can now be slid out of the receiver.
  4. The new barrel can now be installed. Start by sliding it into the receiver. Next, screw on the barrel nut, and then tighten it to the proper torque. Finally, re-install the front sight assembly.
  5. With the new barrel installed, the barreled action can now be reinstalled into the stock. Once it’s in place, simply tighten the action screws to secure it.

And that’s all there is to it! With the new barrel installed, your Remington 700 will be ready to shoot long-range accurately once again.

Olson Staff answered 3 months ago

Remington 700 barrels can be removed relatively easily, particularly if you have the right tools. With a few basic steps, any gun owner should be able to remove and replace a Remington 700 barrel.

How to remove Remington 700 barrel?

The first step is to make sure the gun is unloaded. Next, you’ll need to remove the screws that secure the barrel to the receiver. In most cases, there will be three screws – two in the front and one in the rear. Once these screws are removed, the barrel can be slid off of the receiver.

Once the barrel is off, you can inspect it for any damage or wear and tear. If everything looks good, you can then proceed to reassemble your gun by reversing the above steps.

It’s important to note that you should always use the proper tools when removing or replacing a gun barrel. Using the wrong tools can damage the gun and potentially cause serious injury. Always consult your owner’s manual for specific instructions on how to safely remove and replace your gun barrel.

Jordan Staff answered 3 months ago

First, ensure the rifle is unloaded and confirm that by checking the chamber and magazine. Second, remove the bolt or action from the rifle. On most models, there will be a knob at the top rear of the receiver that you can unscrew to release the bolt.

With the assistance of another person, if possible, place one hand under the front end of the barrel near where it meets the receiver. Apply pressure upwards with that hand while using your other hand to twist off the retainer nut at the muzzle end of the barrel counter-clockwise until it comes free. The Barrel can now be removed from the receiver.

Be sure to consult your owner’s manual for specific instructions on barrel removal for your model as some may vary slightly.

How to remove Remington 700 barrel?

Cruz Staff answered 3 months ago

There are a few different ways to remove the barrel from a Remington 700 rifle, depending on what you’re trying to accomplish.

If you’re simply looking to clean the barrel and/or replace the muzzle brake or other accessories, all you need to do is remove the front sight assembly. This will give you access to the screws that hold on the muzzle brake or other devices. Once those are removed, you can unthread the barrels from the body of the rifle.

However, if you’re looking to do more extensive work on the barrel – such as chambering a new round or replacing the entire barrel – then you’ll need to take a few more steps.

First, remove the stock from the rifle. This will give you access to the action screws, which you’ll need to remove to take off the barreled action. Next, remove the magazine box and floorplate assembly. You should now be able to see the recoil lug, which sits in front of the barrel tenon. The recoil lug needs to be removed to take the barrel off.

To remove the recoil lug, you’ll first need to remove the action from the stock. Once the action is free, you can simply drive the recoil lug out with a drift punch or other similar tool. With the recoil lug removed, you can now unthread the barrel from the action and lift it off.

How to remove Remington 700 barrel?